Cyanoacrylate Adhesive FAQ

Ans. Cyanoacrylates are a family of strong fast-acting adhesives with medical, engineering, and domestic uses. Cyanoacrylate adhesives have a short shelf life if not used, about one year from manufacture if unopened, about one month once opened. Shelf Life of glue may variate depending upon some conditions relating to quantity, quality, curing time and storage temperature. They have some minor toxicity.

Ans. Super Glue was invented accidently while working in laboratory. It is, also known as cyanoacrylate, was initially exposed in 1942 by Dr. Harry Coover, who by the way died last month on March 26th, 2011. Coover was attempted to make clear plastic gun sight to be put on guns used by Allied soldiers in WWII.

Ans. Acetone dissolve Glue bond. Acetone is sold at the hardware or chemist stores. In case of availability you may also try nail polish remover which also have acetone in their composition.

Ans. Do not attempt to tear or force apart the glue. This could rip your skin. Apply acetone-based nail-polish remover to the part. The acetone breaks down the glue bond.

If there's a lot of glue on your top, steep the skin in nail-polish remover to melt the bond. Clean the area with soap and water after removing the glue. If you don't have nail-polish remover,steep the affect skin in warm and soapy water. Slowly roll the skin to work the bond apart as the hot water soak through. Continue doing this pending the skin is free of glue.

Ans. When CAs cure they volatize, creating the appearance of a white haze around the bond line. This phenomenon occurs when the cyanoacrylate monomer react with moisture in the air, and settles on the part. On areas where this may be a problem, our company have special grades for this type of application. This grade is also known and non-blooming grade.

Ans. Most surfaces are not smooth. Glues fill the gaps, building a bridge between the 2 surfaces and after thatharden due to the moisture in the air keeping the bond together. If the surface is plane and smooth then Low viscosity grade can work well. But on rough surface high viscosity glue or gel may be applied to fill the gaps.

Ans. In general 1 drop is enough for 1square inch joint. Less glue is enough - excessive glue can makes a bond weaker.

Ans. Bottle is itself designed as a Universal applicator. Extra-long nozzle may be supplied on request if needed for pin point precision applications on hard to reach places and small spaces.

Ans. cyanoacrylate adhesives are not poisonous. The fumes from cyanoacrylate adhesivegets vaporize and do bother sensitive membranes like eyes, nose and gullet. When these vapors come in contact immediately polymerize when comes in contact with clammy surfaces. They do not effect and penetrate into human skin tissue. There are many applications where specially formulated medical grades of cyanoacrylates have been used to graft skin, bond bone and cartilage, renovate eye hankie, close blood vessel and stop spinal liquidleak.

Ans. Cyanoacrylates are best to store in their original container in a cold temperature below 20 degree Celsius, in dark, and dry location. The shelf life of general purpose cyanoacrylates stored at room temperatures can be up to six months to one year depending upon offered grade.

Ans. We are specialized and offer tailor made solutions to our clients and develop grades as per special needs of our users. There is no "one" perfect adhesive that works best on all materials cyanoacrylates are used for the following reasons: quick cure, single component, high tensile/shear strength, able to bond similar and dissimilar materials, easy to mete out, low for each unit cost, and a variety of other factors. There may be different type of grades which may variate in terms of viscosity, shelf life, curing speed, blooming or non-blooming in different range of packaging.

Ans. The biggest reason is less overheads and bulk production. We always kept our overhead very low in order to offer lower cost cyanoacrylates to the Industrial Market. Being in the cyanoacrylate business for many years we offer best quality industrial cyanoacrylates to all industrial customers at the lowest prices.

There are perhaps thousands of applications where cyanoacrylates are used to save developed time and money. Here is a small list: flex pasting or sign board making, footwear manufacturing, helmet, Automotive trim, ganging batteries, bow/arrow vanes, cell phone covers, printed circuit board application, beauty cases, dental application, throwaway medical products, fishing lures, furniture and other repair, guitars, hearing aids, honing stones, jewellery, lamp shades, finger print identification, loud speakers, luggage, mortuary applications, oil filter, o-rings, RC plane/cars, rubber mats, security packaging, shoe repair, silk screens, steering wheels, toys, transformers, weather stripping, etc..

Ans. CA glue, instant glue, cyanoacrylate, and super glue are different names for cyanoacrylate adhesive. Even though these all explain the same type of glue, changed groups of users use.

Ans. Cyanoacrylate adhesive can bond almost everything but there are some tough application like bond on HDPE, LDPE, PP, Teflon, foam, mirrors and greasy surfaces is not possible, but in some cases it may acquaintance by applying particular grades. There is bond failure in parts that have regular vibrations.

Ans. The shelf life of cyanoacrylate adhesives is limited up to few months depending ahead grades, bunch size, and class and curing speed. So after expiry it is definitely going to be dried.

Ans. POLYFIX® Instant glue will form a tough bond in about 30 to 60 seconds so you can usually just hold pieces in place until the bond sets in few minutes.

Ans. POLYFIX® INSTANTGLUE in the tip of the nozzle is reacting with moisture in the small orifice gets hardens. Normally once the instant POLYFIX® CA harden the consumer will take a pin and join it down into the needle to open it up only to find it block up even earlier the next time. What happens is the pin scratch the inside of the needle, which allows even more POLYFIX® CA to stay in the needle cause it to block up faster. This method will be frequent sometimes until the nozzle is no longer able to be used and gets thrown away.

Ans: When using CA to bond glass, the power is firstly strong but degrades radically over time. The cure speed is particularly fast due to the basic nature of glass which likely generates high stress in the bond line instantly adjacent to the glass at a molecular level. This high stress makes the cured polymer around the bondline susceptible to chemical and physical degradation as a response overtime to tightening and growth of the joint with changes in temperature, or hydrolytic attack by moisture, etc. A permanent bonding in joints cannot be achieve when bond substrates involving glass.

Ans: cyanoacrylates adhesives are acid stabilized, single component adhesives that react quickly at room temperature when contacted with moisture (a weak base) or dust particles between tight bond lines.

This usually depends on what type ofsurface on which glue is to be used, if the surface is uneven the glue will be consumed more and if surface is even and smooth then consumption of glue will be less. Apply a thin, uniform layer that may completely covers the surface area to be glued.
Make sure the surface is clean, dry and free of debris. For smooth, hard surfaces, use sandpaper or steel wool to gently roughen the surface before gluing to get a stronger bond.
The best thing to do is simply seal the cap tightly& storing the adhesive according to the temperature required.
Blooming or frosting is a phenomenon when cyanoacrylate monomer volatilizes off a part, reacts with moisture in the surrounding environment, and falls back down on the part leaving a white powdery residue behind. There are several ways to prevent blooming such as sufficient ventilation over the assembly area, applying less adhesive and curing the adhesive faster. Or ask company for non-blooming grade.
High viscosity cyanoacrylate curing speed is slow in nature,Instant adhesive accelerators are solvent-based products that are pre-applied or post-applied to increase the cure speed and increase the gap-filling capabilities of instant adhesives.
Most glue doesn't stick to the inside of the bottle because it needs air in order to set. If you leave the cap off of the bottle or as the bottle gets closer to empty so that more air is inside the bottle, the glue will get stickier. Some types of glue require a chemicalother than those found in air. These types of glue won't stick to the bottle even if you leave the cap off.
The vapours of cyanoacrylates are irritating and workers should not be exposed to them for long periods of time. In many cases the use of our "Low Odour" and "Low Bloom" products can be used to control the irritating odour. Or otherwise use glue in proper ventilated area.
Yes, Polyfix will bond granite anywhere. What you could do is apply the adhesive only to the cracked parts, then align the piece back to the counter, when you are satisfied with the alignment spray the Polyfix Activator and hold it for at least 20 seconds, that will lock it in place.
Polyfix products are available online (https://bit.ly/30jDINO) as well as on retail shops. For bulk orders please contact our office: Benson Polymers Ltd. 3 L.S.C.3 3rd floor Rishabh vihar karkardooma Delhi 92
Yes, you can use Polyfix gel glue without the activator if time is not a factor,also you can slow down the curing time by not using the activator and depending on the materials used. The activator is used only when you need to cure immediately or hold parts in place instantly. If time is not a factor than the adhesive can be used alone.
The main characteristic of Polyfix adhesives is that they cure instantly on demand eliminating the use of clamping devices or hold down methods. Our claim is the “no hold” freedom which offers new possibilities in the repair, installation and/or building methods that were not available before. Its most important attribute is that it is not only an extremely strong and versatile adhesive but cures instantly on demand with the introduction of a new aerosol accelerator agent. This is what really sets apart Polyfixfrom all other adhesive products.
Yes Benson Polymers Limited can make glue as per requirements of customer and even may manufacture slow cure CA adhesive.
Shelf life is greatly dependent on storage conditions, high temperature and high humidity and direct sunlight effects and reduce shelf life. If stored below 20 degree the normal shelf life should be approx. 5-6 months. Shelf life can be dramatically lengthened by storing the adhesive in cool and dry place away from direct sunlight.
Yes, Polyfixdoes a great job bonding metal and wood, or other dissimilar materials, just apply the adhesive on one side and spray activator on the other, hold the parts together in place for a few seconds and you’re done. If you need more time to align the pieces, put the adhesive on one piece and put the pieces together, feel free to align then liberally spray the activator on the seam while holding tightly, allow this method more time for the activator to penetrate the seam (30-60 seconds depending on the material) before applying any exertions or use.
Attain amazing speed and strength with Polyfix. No need to wait for messy products to dry. Polyfix instantly bonds wood, stone, plastic,metals, ceramics, etc.
Yes. Direct human or animal contact. Polyfix Adhesives should not be used to assemble, or repair substrates that will be used with food and water.
Polyfix adhesives offers low, medium & high viscosity products. Low viscosity cures within 1 minute, medium viscosity takes 3-5 minutes to adhere & high viscosity can cure within 8-10 minutes.
Yes from Polyfix high viscosity instant woodglue it is possible to bond all above boards available in market. MDF bonding is superb by using polyfix instant wood glue.
Polyfix WPC glue eliminates the total use of nails & screws. Only using Screws are not a good option to join WPC boards as they gets loose over the time and do not stay in their place. Polyfix WPC adhesives gives super strength to the bonding & does not need any support but screw may be used if user needs it necessary.
PolyfixDebonder removes glue stains from any surface. In case of clothes, we recommend the use first on a small area for testing. If satisfied, the whole area should be cleaned with Debonder.
Cyanoacrylate glues (famous brand POLYFIX) should always be stored away from direct sunlight. Bottles should be stored below 20 degrees, to avoid any wastage.
A- Polyfix Spray Activator is used when instant pasting is required with Polyfix Gel glue. It is basically used to expedite the curing time of glue. It is not to be used when more repositioning time is required.
Polyfix offers special shoe grade adhesive for repair & manufacture of shoes & footwears. It is instant & gives strong bonding.
Full cure time is the time to reach full strength. Fixture time is curing to partial strength where light handling can be done. Cyanoacrylate adhesives ( POLYFIX instantglue) gain most of their strength very quickly, but the remaining strength takes a bit longer.
Cyanoacrylate adhesives (Polyfix Instant Glue) cure when exposed to moisture, and since there is moisture almost everywhere, they react well on almost every surface. Leaving some exceptions like PP, HDPE, LDPE surfaces.
Cyanoacrylate gel adhesives( Polyfix Instant HV Glue) work best for porous surfaces since they fill the small gaps between the surfaces far better, and best suitable for paper, leather, wood etc
Yes, Cyanoacrylate adhesive ( POLYFIX instantglue) works well on flexible surfaces like rubber, If Required Flexible glues are also available with rubber additives for applications where movement or vibration may affect the joint.
A- For manual applications, you need to start with a clean, dry surface. Apply CA(Polyfixinstantglue) to one of the parts, then quickly press the parts together and hold them until the glue sets, usually anywhere from a few seconds to up to a minute. Don’t spread out the drop or bead, but instead let it squash when you join the parts. Use the smallest amount you need. Excess glue does not add more strength. CA cures slower on some surfaces, but you can use an accelerator to overcome that.
Polyfix offers high viscosity glue which has accurate composition for pasting of surfaces like MDF, MICA, PVC, WPC etc. It has thick consistency which has the power of not getting absorbed by the surface & gives excellent pasting in minimum time.
Polyfix spray activator is solvent based, which when used with CA glue gives instant cure. High viscosity cyanoacrylate glues need some time to get set, our spray activator is used to expedite the curing time for the same. It can be used with other viscosities as well.
Wood fillers or wood seal are offered by Benson Polymers specially for repair of the holes & gaps on the wood surface. Polyfix wood seal is a low viscosity CA glue which when used with baking soda or sawdust gives best results.
Polyfix cyanoacrylate adhesive for acrylic sheet pasting are Cyanoacrylate based to give best performance. We offer different viscosities for acrylic pasting applications. Our acrylic non blooming adhesive gives instant pasting, strong hold & most importantly does not leave any marks on the surface.
The right consistency CA glue will definitely paste wood. High viscosity Polyfix wood glue has been specially designed for pasting of wood. Low viscosity adhesives get easily absorbed by the surface & does not give any pasting, whereas high viscosity thick adhesive provides superior bond as it easily fills the gaps & initiates rapid adhesion.
Benson Polymers ltd is known for providing a variety of CA glues with brand name Polyfix. These are mainly segregated by low medium & high viscosities. Each viscosity has different applications. Low viscosity is the thinnest & fastest adhesive used for minor repairs or small manufacturing. Medium viscosity is slightly thicker than the low viscosity glue & helps in curing minor porous materials like cloth. High viscosity is the thick version, which helps in filling the big gaps/pores in surfaces like wood.
When you are pasting two pieces, it is not necessary to cover both surfaces or even one entire surface. Instead, apply the glue in a spiral pattern. Do not apply a thick layer of CA glue to pieces you are bonding. As the thickness of the layer of CA glue increases, the curing time and the chance of glue in the middle not fully curing increases.
The Polyfix spray activator is an accelerator which is used to expedite the curing of CA glues. It should not be used when more repositioning time is required while bonding surfaces.
We recommend to look for unusual properties such as a change in consistency. If the material still looks normal, do a testing by bonding two pieces. If the bond strength is as per satisfaction, please go ahead and use.
Substrates should be in satisfactory condition, clean & dry for best results.
Polyfix adhesives are instant in curing. They are very cost effective as they save manpower, time & money. Any kind of clamping is not required with Polyfix adhesives & only a little amount of adhesive can do the work.
Polyfix Cyanoacrylate Gel glues are best when gap filling is needed. Gel can fill bigger gaps and is recommended for porous materials such as ceramic and wood.
It is always best to clean the surface before applying. Be sure to remove all grease, dirt and rust.For grease and dirt use a clean cloth with a liquid cleaner and let dry.
Anaerobic adhesives, also known as impregnates, are required to cure in the absence of air, unlike surface sealants that require air as part of the curing procedure. Adhesive sealants are used to prevent the penetration of air, gas, noise, dust, fire, smoke or liquid.
Polyfix offers coloured cyanoacrylates like black & blue CA glues. These are used as marking adhesives. Black cyano is also rubber toughened.
POLYFIX Spray activator has been formulated to expedite the curing time of high viscosity adhesive but it can be used with other adhesives also. However, low viscosity already has a curing time of a few seconds, so the use of spray activator is not mandatory.
After the nose is cut, store the bottle vertically & squeeze it gently to make sure there is no remaining glue in the applicator.
The only difference is that the superglue aches a little after you put it on. Surgical glue and superglue are both POLYFIX cyanoacrylate glues. The big difference is that surgical glue has been formulated to avoid that burning sensation at application.
What is the difference between medical glue & normal POLYFIX cyanoacrylate adhesive?
Polyfix Nail glue can be used for nail art & to paste rhinestones, crystals, beads on false nails.
This product itself doesn't cause much direct damage to your nails. Caution must be paid while removing. Soak hands in warm water & remove carefully with nail polish remover. Do not pull or handle roughly.
We list unique properties of each Polyfix CA glue and the different applications that have been successfully performed. For example, thick CA adhesives are ideal for porous surfaces, surfaces with minor gaps, so that the glue does not get absorbed & gives best pasting. Thin CA adhesives are used for day-to-day small repairs & instant pasting.
Viscosity can simply be thought of as the thickness of a fluid. Polyfixprovides you with low, medium & high viscosity CA glues. Polyfix offers a wide selection of viscosities to suit various applications.
Once the curing process is complete, It is observed that Polyfix adhesives have water resistant properties.
Polyfix cyanoacrylate glues are safe to use with most materials and for every kind of our CA glue, we list various compatible materials. However, it is advised to test a drop of the CA glue on the material before proceeding.
CAs bond well to wood, rubber, fiberglass, carbon fiber, metal, and most plastics(except PE, PP). CAs do not bond well to foam, silicone, and extra smooth surfaces. While pasting extra smooth surfaces, they should be roughed a little with sandpaper.
Polyfix cyanoacrylate adhesives are instant bonding glues. Our products only need a little contact pressure to initiate the bonding but any kind of clamping is not required.
PolyfixDebonder is ideal to remove super glue from a lot of substrates. It is an acetone-based liquid which easily removes cured or uncured CA glue.
Polyfix glues are used to bond a lot of substrates, ideal to paste small items & are the best repair adhesives. We have the best cyanoacrylate adhesives, water-based adhesives, nail glues, medical glue etc.
CA glues are not toxic but they can be eye-irritants & sometimes may give a strong chemical odour.
There are no direct harmful impacts to the environment, when working with CA glues it is recommended to work in well ventilated area.
How to ready the surface before applying the adhesives?
Most of the modular kitchens use PVC foam board or WPC boards. Polyfix provides WPC/PVC adhesive for best pasting of these boards.
These are water resistant to some extent. Occasional splashes of water would not compromise the bonding strength.
Normally, these shouldn’t cause any lasting damage. However, while working with these precautions must be taken. Always work in a well-ventilated area, wear protective gloves & keep away from skin & eyes.
CA glues are fast working, attains adhesion within seconds. These are also cost effective, gives high strength bonding & easy to use.
We offer Polyfix Spray activator to accelerate the curing speed of super glues. Just apply glue to one surface & spray the activator on the other.
The main ingredient in super glue is cyanoacrylate, which is an acrylic resin that cures almost instantly.
The curing depends on the viscosity of the adhesive. Low viscosity glue takes seconds to dry, medium viscosity needs 2-3 minutes & high viscosity needs 8-10 minutes to get initial bonding.
Polyfix Debonder can be used to dissolve cured glue. Just pour the liquid debonder on the glue & clean with a cloth or a metal strip.
Benson Polymers offer VAE water based adhesives for pasting of fabric or special fabrics like denim. This adhesion is tricky as most adhesives are not compatible with fabrics. Our brand adhesive provides quick & strong bond to fabric as it is water based. The water present in the adhesive is absorbed by the fabric so that the glue can work through the surface by locking it. Once dried, the water-resistant property gives a superior bond.
Polyfix instant high viscosity glues are ideal for rough & jagged surface like that of porcelain. It can be used in manufacturing or repairing porcelain objects. The thick glue easily locks the holes & gaps present on the surface & lets the adhesive work on an instant & super strong bond.
Polyfix artificial nail glue gives superior bonding without any hassles. It can last for 15-20 days with proper care. For long lasting pasting, avoid keeping hands in water frequently.
Polyfix WPC/PVC adhesives gives great & quicker adhesion with PVC doors& windows panels & frames. It will provide best pasting in less time, without any heavy clamping.
Polyfix high viscosity adhesive suffices for small repairs & slight pasting in leather shoes but it is not recommended for bigger applications.
Broken ceramic can be repaired perfectly with Polyfix high viscosity glue. For further acceleration & more strength we recommend the use of Polyfix spray activator along with the adhesive.
Polyfix products are used in footwear manufacturing & repairs, automatic assembly lines. It can repair small cracks & soles also. Adhesive bonding can depend on the type of shoe surface. It is recommended to test the adhesive on a smaller area first, to see the results.
Polyfix high viscosity glue is ideal for fixing & pasting marble slabs. It gives quick & superior bonding.
We offer adhesives particularly for acrylic grade. Our non-blooming acrylic adhesive gives best results with transparent acrylic sheets. The use of Polyfix spray activator is highly recommended for instant & absolute stain free product. It can be used to make acrylic boxes, fish tanks etc.
Plastics have super smooth & slippery surface, the lack of roughness makes it difficult for the adhesive to bond with anything. Polyfix covers adhesion of wide variety of plastics. It is not recommended for some plastics like HDPE, PP. Adhesion will depend on the type of application.
We offer Drop Bond UV Glue 3030 & 3036 for pasting of glass sheets. It provides superior strength & efficient bonding. 3030 can paste glass to glass for horizontal bonds & 3036 is a premium grade which can paste them vertically and may bond metal, acrylic sheets also.
Polyfix high viscosity glue is best suitable for porous surfaces because of low absorption. the glue can fill the minor gaps & holes & start the bonding process. It is fastest glue available.
Use Polyfixdebonder for the same or soak the bottle in hot water for a couple of minutes.
It is made up of cyanoacrylate, an acrylic resin that reacts to form tight chains between two materials being bonded, when it comes into contact with moisture in the air.in India famous brand is POLYFIX cyanoacrylate adhesive.
Superglue works well up to temperatures as high as 80°C and have good water resistance, however, too much exposure to extreme heat will cause the strength of the bond to weaken and similarly, exposure to too much water, especially warm water will also cause the bond to weaken.
An epoxy adhesive is double component, It also have pot life& takes a lot of time. A superglue, a special grade POLYFIX HV glue however is ideal to use when the surfaces are multiple like metal, tiles, PVC sheet, Foam board, wood, Stone, marble etc. an instant bond is required. Super glues are single component.
A- Whenwe paste MICA with PVC Foam Boards, generally water-based adhesives is used as it is conveniently available. But it is not right choice because of reason that both MICA and PVC foam board are water resistant and surfaces are not water absorbent, For perfect pasting, the water content in the adhesive needs to be absorbed by the surfaces. Due to this the water content in the adhesive remains as it is in the pasting. During hot conditions, the water tends to evaporate, which results in puffing up of the substrate & ultimately becomes damaged. Polyfix high viscosity adhesive is 100% solid and do not contains water contents and cures immediately. Our adhesive provides perfect & strong pasting within a few minutes. This helps in avoiding any screws & no white adhesive is required.
A- Generally, workers apply white water-based adhesive to paste PVC foam boards & MICA. It is seen that after some time the surface gets turned, puffed up or damaged after sometime. This happens due to the water present in white adhesive. PVC foam boards & MICA both the surfaces repel water as they are not absorbent in nature. Whereas the white adhesive’s water content needs at least one surface which can absorb the water. For this pasting, Polyfix cyanoacrylate adhesives are ideal, which is 100% solid & do not have any water content in them. These are high strength adhesives which are single component, easy to apply, instant drying & cost effective also.
A- Polyfix offers high viscosity CA adhesives which are efficient & come with superior strength formula. These cyanoacrylate glues have the best pasting& are ideal to paste many different surfaces like wood, stones, rubber, acrylic, WPC, PVC foam boards, granite, marble etc. PVC foam boards & MICA needs adhesives which should not have any water content in them. Normally water-based adhesives are used to paste these surfaces but being water repellent PVC foam boards & MICA does not give proper pasting to these surfaces. If white adhesive is used for this then the substrates get damaged after some time. For undamaged & durable pasting, PolyfixHV CA glues should be used.
A- Due to absence of proper knowledge, PVC foam boards & MICA surfaces are pasted with white adhesives, which are water-based. These adhesives give initial pasting but the results are not durable & the surface gets damaged after some time. Either it gets turned/ puffed up or swollen. Both these substrates are water resistant & white adhesives have water content. Because of this the substrates get damaged. To prevent this damage, PolyfixHV cyanaoacrylate glues should be used. Because of no water content, CA glues give best pasting. It grasps the surface within a few minutes & initiate strong pasting.
No. It is waterproof but it is not suitable for permanent underwater exposure.
Clamping is not necessary, unless the material to be bonded is very heavy, in which case it will be necessary to hold them for some time until the adhesive dries completely
If your joint or glue-line needs to be painted over, then use a Polyurethane sealant as silicone sealants cannot be painted over. Polyurethane sealants are suitable for use in contact with most building materials whereas silicone sealants are not suitable for adhesion to cement and concrete and other strong alkali surfaces.
UV Adhesives are transparent adhesives that bond acrylics, glass and metals. They remain in a liquid state until they are exposed to UV light.
It is recommended to wear protective gloves & eyewear while using UV adhesives. Never look directly at the UV light source and always use the UV light in a protected area. Ensure you read the adhesive safety datasheet before using the glue. Always read the operator safety instructions when using high intensity UV light
Ideally any glue should not come in food contact to avoid any complications.
Polyfix cyanoacrylate glues are solvent based & white adhesive (Polywood) is water based.
We have various packings available according to the viscosity & product type. The packaging can also be customized as per client’s needs.
They can be used for all kinds of woods, paper, card boards, MDF, Mica etc. Our POLYWOOD may also be used to paste PVC sheets on porous substrates.
By porous, we mean surfaces which can absorb water or let moisture penetrate.
Even if one substrate is porous then also the water content present in (POLYWOOD) white adhesive can be absorbed & the bonding may be achieved.
Polyfix WPC instant glue is best adhesive for modular kitchens, WPC boards & PVC foam boards with mica or PVC sheets.
Polyfix High Viscosity Wood adhesive is the best option for wooden furniture.
You can directly contact our office or buy through our dealers. Polyfix products are also available online on amazon, flipkart (https://www.flipkart.com/search?q=polyfix&otracker=search&otracker1=search&marketplace=FLIPKART&as-show=on&as=off&as-pos=0&as-type=HISTORY) & shopclues.
A- When you are bonding two pieces, it is not necessary to cover both surfaces or even one entire surface. Instead, apply the glue in a spiral pattern. Do not apply a thick layer of CA glue to pieces you are bonding. As the thickness of the layer of CA glue increases, the curing time and the chance of glue in the middle not fully curing increases.
A- There are several factors which determine how fast instant glue will dry. A common reason for CA glue not drying is that the glue being used is too thin for the joint. If CA glue is not being pressed between two surfaces and has not had accelerator applied, it will take a long time to cure, and if the glue is too thin for the application, it will still not create a bond when it does cure.Another factor in curing time is the material being bonded. Different substrates cause instant glue to dry at different speeds. Metal surfaces are very slow cure,Oils and other contamination on the surfaces can cause the glue to bond slowly, weakly, or not at all.
For stone pasting, cyanoacrylate adhesives are the best as they are single component, easy to use, cost effective & quick drying. Polyfix provides high viscosity adhesive for difficult surfaces like marble, stone, granite, wood etc.
Polyfix Debonder, provided by Benson Polymers ltd. is an acetone-based liquid which helps in removing cured & uncured super glue marks, blobs & stains from most of the surfaces.
With screws, the problem comes in terms of durability, with frequent use, screws become loose but Polyfix high viscosity wood glue will not lose its pasting power & ensures durability.
Diluting wood glue is not recommendable because it can decrease the bonding power of the adhesive. However, water-based wood glue can be diluted with 5% water by volume, or you can thin it a little by placing the container in hot water.
Polyfix Wood adhesive gives best results. Wood is a porous substrate & it absorbs most of the adhesives. Polyfix instant wood glue is a high viscosity adhesive that can block the holes & gaps present on the surface & provide a thin layer of glue for adhesion. It takes a decent grip within 10-15 minutes & attains full adhesion within 24 hours.
Polyfix WPC Instant Glue, is a high viscosity adhesive which surpasses the double component & water- based adhesives available in the market for pasting plywood. Polyfix WPC glue works better as it is a single component cyanoacrylate adhesive. It gives superior strength in minimum time.
Polyfix WPC glue is best solution for multiple bonding applications and may bond PVC, wood, stone, rubber, metals etc in about 20-25 minutes and it is single component and needs no mixing.
Polyfix Methyl Cyanoacrylate Adhesive is a single component clear transparent adhesive having Medium & High viscosity. This glue is slow curing at room temperatures and it is best suitable for bonding mainly metals, steel, & aluminum surfaces.
Polyfix cyanoacrylate-based WPC glue has been specially formulated for WPC boards bonding. It works better than most of the adhesives as it is water resistant, heat resistant & provides superior adhesion to WPC boards. It is ideal for making WPC furniture, closets, drawers, modular kitchens etc.
Benson Polymers provide Polyfix spray activator which when used with adhesives, adheres rapidly without any clamping. With the use of spray activator, the task which normally takes a couple of days, can be done within a very short span of time.
Super glue is not known to evaporate but it cures as soon as it comes in contact of air. In case the lid is not closed firmly after use then the quality may deteriorate.
Polyfix glues have a variety of grades which are used for repairs & manufacturing. It works on substrates like wood, leather, metals, some plastics, stone, marble, rubber, acrylic, flex etc.
Polyfix Spray Activator is an accelerator which is used with cyanoacrylate glues to expedite the curing time. Polyfix spray activator, when used with adhesives, adheres rapidly without any clamping. With the use of spray activator, the task which normally takes a couple of days, can be done within a very short span of time.
Polyfix instant high viscosity glue is used widely to paste substrates on leather. Our adhesive can be used to paste logos or metal objects on leather. It finds heavy usage in making leather bags, purses, wallets, jackets etc.
Polyfix high viscosity glues, can easily join broken ceramic bowls. It has gap filling properties, easily chokes the holes on the surface & initiate rapid bonding.
PolyfixPVC glue works wonders in this application & provides quickest & strongest bonding. Our adhesive is known for PVC foam board pasting, WPC to WPC bonding etc. The heat & water resistance of our PVC adhesive gives durability to the boards. It is cost effective & attains full strength within minutes.
Polyfix adhesives are CA glues with super strong hold. We provide cyanoacrylate instant glues in different viscosities & properties. The rapidly working Polyfix adhesives provides best & strongest pasting in very less time. They save time, money & manpower.
Polyfix High Viscosity glue is ideal for this application. Polyfix adhesives provide strong pasting in very less time, that too without any clamping. It gives more repositioning time to get exact & perfect pasting.
Benson Polymers ltd offers N-Octyl Cyanoacrylate &N-Butyl 2- Cyanoacrylate medical glue for the same. The ability of this glue is to initiate a rapid & effective wound closure with a minimum tissue deformation and without risk of Needle-Stitch injury.
We provide high viscosity adhesive for this purpose. Due to the thickness, this glue is ideal to repair jagged & rough surface of marble. It easily fills the holes &pores of the surface & provides superior strength pasting without any clamping.
Polyfix thick high viscosity glue is best to bond wood to plastic, wood to wood, wood to stone, wood to MDF, WPC to WPC etc. Our glue has the right consistency to bond tricky substrates. Because of the thickness, the wood adhesive does not get absorbed by the surface & initiate bonding within minutes.
Instant curing glues should be used under adult supervision for younger children but water-based glues or craft adhesives are safe for kids to use.
All Polyfix adhesives are safe when handled as per instructions. It is best to work in well ventilated areas as fumes can be irritating but they do not possess any danger.
Most adhesives cure at room temperature, if the temperature is lower, than the curing will take time.
Too much adhesive doesn’t work & does not give a good finishing. Less is more with adhesives. Only little amount of adhesive should be used & on one surface only.
There are many brands of CA glue availablein the market. While they are the same type of adhesive but none of them can offer the same level of performance and reliability at our prices. Polyfix instant glues are used by professionals working with expensive or rare materials and in critical applications that demand the highest strength and reliability.
Polyfix Instant Wood Adhesive is a cyanoacrylate-based adhesive which is best suitable for all wood working projects. It is a thick glue which does not get absorbed by the porous surface of wood & gives instant & best pasting without any clamping.
CA glue bottles should always be kept in cold storage for better functioning.
Polyfix debonder is an acetone-based liquid which when poured on cured or uncured glue, helps in cleaning all the stains & glue residues.
Most adhesives cure only above 5 degree Celsius & some can only cure at room temperature.
Some of the reasons which can affect the bonding are: If the correct adhesive type is not used for a particular substrate. If the correct quantity is not used. If the surface is not clean of grease, oil, dirt etc.
Polyfix low viscosity CA adhesives are best for footwear applications. It gives instant curing with superior strength.
We offer fabric glue for fabric pasting. It is also used for pasting of denim patches & making of denim bags, jackets etc
A- Benson Polymers provides Medical glue which can be used for closing small wounds, as per Doctor’s instructions.
Every adhesive has different grade & properties. Similarly, the shelf life depends on the adhesive type being used.
In case of contact with eyes or mouth, rinse thoroughly with water & take immediate doctor’s help. If the fingers get stuck together then dip the fingers in warm water & try to open them gently.
Cyanoacrylate gel adhesives work best for porous surfaces since they fill the small gaps between the surfaces far better.
One should use flexible glues which are available with rubber additives for applications where movement may affect the joint.
No, but Super Glue is cyanoacrylate. Certain types of Cyanoacrylate are referred to by the generic term super glue, as it identifies instant and strong-bonding properties that people know.
The main types of cyanoacrylate are methyl 2-cyanoacrylate, ethyl-2-cyanoacrylate, referred to by the generic term superglue, and n-butyl cyanoacrylate and 2-octyl cyanoacrylate, which are both used in medical applications.
Cyanoacrylate gel is a very high viscosity product that adheres well to porous surfaces. Most basic cyanoacrylates have a very low viscosity, which can make handling difficult. Trying to adhere a low viscosity product to a rough surface or a vertical wall, does not work. The product often runs off. Gel forms of cyanoacrylate provide the ability to adhere to surfaces where resistance against gravity is needed or where the glue needs to fill surface gaps.
cyanoacrylate that is toughened by an additive, typically rubber to increase shear strength. Cyanoacrylate's weakest point is in shear strength. Adding toughening agents with elastic properties, such as rubber, help toughen basic cyanoacrylate formulas for higher strength applications, particularly for improved shear strength. Toughened cyanoacrylates take slightly longer to cure than normal super glues and may need an accelerator if fast cure times are needed.
Polyfix Spray Activator can be used to speed up the curing time where very quick bonding is needed or in very cold or dry conditions.
No, there is a group of Cyanoacrylates that are called “toughened”. This group is usually black, but also comes in Clear, and is rubber toughened. The rubber gives it some flexibility which is ideal for applications that are in an environment that might have minimal vibration or shock.
Most Thread Lockers have a fixture time of less than 10 minutes and full cure time of 24 hours.
It is not recommended.
Store in a cool, dry place. Bring to room temperature before using.
Generally, they are recommended for use on metal surfaces. Some materials are more active than others and the curing speed may be faster or slower.
Anaerobic threadlockers need metal ionization and the absence of air to cure, such as when a nut is screwed onto a bolt, squeezing out the air – and hence, the Anaerobic drying and locking.
It depends on the Size of the bolt, and the temperature It should also be seen whether the adhesion is removable or permanent.
Polyfix offers flex grade adhesive for pasting of banners. It helps in making signages, backdrops, standies on metal frames. It is a low viscosity glue which gives best & strong pasting in seconds.
Use Polyfix flex grade adhesive to paste banners on metals frames. It is the best available glue for this application. It is a CA based adhesive which gives fastest adhesion to flex.
Benson Polymers provide Polyfix instant flex glue to bond flex to iron/metal frame. This is undoubtedly the best flex adhesive as it is instant in pasting, cost effective & gives durable pasting. It is a cyanoacrylate-based product which acts instantly. Normal adhesives need clamping to get full pasting & still do not offer strong pasting. Whereas, Polyfix flex adhesive works with little pressure & gets full pasting in just a few seconds.
Polyfix instant flex adhesive, not only gives rapid & strong pasting but can sustain harsh climate conditions. It is a water-resistant adhesive, due to which it promises durability. The pasting attained, can successfully sustain rainy and moist weather conditions also.
Polyfix medium viscosity CA adhesive is best suitable to paste cloth banners. It helps in filling gaps present on the cloth & gives superior pasting immediately. It saves time, money & manpower. Polyfix is the best cloth banner glue to make banners, backdrops etc. Please watch our https://www.youtube.com/watch?v=MqsqBjgtWTM for further information.
Cloth banners can be pasted on metal stands with Polyfix medium viscosity cyanoacrylate adhesive. It is a special adhesive which is used to adhere cloth to metal frames. Being slightly thick it does not run & fills the gaps present on cloth surface. It is a cost-effective adhesive which gives strong hold & durable pasting.
Being environment friendly, cloth banners are creating a strong market in signage industry. But pasting these effectively is a big challenge. Due to ignorance or lack of knowledge about correct adhesive, workers use white adhesives to paste cloth banners which is not durable. Polyfix offers medium viscosity glue which is ideal in making cloth banners & hoardings. It is a CA-based adhesive which cures almost instantly. It covers the small gaps on the cloth surface & give best pasting even in difficult weather conditions also. Watch our video https://www.youtube.com/watch?v=SAiekt8iVdg .
Usually due to harsh climatic conditions like high temperature, wind pressure & heavy rainfall, many adhesives lose their pasting in flex banners. Polyfix instant flex adhesive is one of the strongest adhesives present in trade. It is cyanoacrylate-based which can withstand high & low temperatures to quite an extent. It provides much more long life to the pasting, as compared to other adhesives available in the market.
Polyfix low viscosity flex adhesive is known in the market for its instant pasting. To paste effectively only a few drops of the glue are enough & just a little contact pressure is required. It can paste the flex to iron stands in 3-5 seconds. Watch our https://www.youtube.com/watch?v=SAiekt8iVdg to see the procedure.
Polyfix flex glue is a low viscosity glue that takes only 3-5 seconds to dry and to get the initial bonding.
Polyfix instant CA flex adhesive needs moisture to start the curing process. During very high temperature, there is a dearth of moisture in the air, which is why the curing may take time. Otherwise, Polyfix instant flex glue is the ideal product for pasting of flex to stands.
Use Polyfix flex grade glue to get ideally pasted flex to iron/metal stands. One should take care of the following steps while working: • The stand should be clean of any water droplets or grease. • It should be rust free. • Protective gloves should always be worn while working with glue. • Apply the adhesive to only one surface. • Work in a well- ventilated area Watch our video https://www.youtube.com/watch?v=MqsqBjgtWTM to see how to make a signboard with Polyfix.
Water based adhesives can work on porous surfaces, which can absorb their water content. As flex & iron frames both are non-porous the white adhesive does not work on them. Polyfix has just the right product for this, as Polyfix flex glue is a cyanoacrylate adhesive which works instantly on flex. It does not have any water content which is why it gives ideal pasting to iron/metal frames. Watch our https://www.youtube.com/watch?v=SAiekt8iVdg to see how to make flex banners.
Generally, small flex pieces are pasted together to make bigger hoardings. Polyfix flex grade adhesive is ideal to bond flex to flex. It is a thin adhesive which gives stunning pasting in minimum time. Also, when these flex boards are mounted at high altitudes then there is a possibility of the flex being damaged due to heavy winds. Polyfix glue is capable of solving this problem also. Once the flex is fully pasted then there is absolutely minimal chance of it getting ripped even in high wind pressure.
Polyfix instant flex glue is a unique adhesive which gives instant pasting to flex & iron frames. It gives strong bonding in mere seconds, so the workers do not have to clamp it & wait for ages for it to dry. It saves time & money & the production output can be doubled in the same time. The bottles are designed specially to help workers paste the flex at high altitudes. Please watch our https://www.youtube.com/watch?v=SAiekt8iVdg to get further information.
Polyfix flex grade adhesives are a renowned name in the signage industry. Polyfix Instant Glue not only sticks flex to the frame instantly but the strength received is unmatched. The performance is similar for both heavy & light weight banners. With the help of Polyfix glue, once the pieces are bonded, they will not budge even in fast blowing wind. The fast curing speed results in high production in minimum time. We provide both PVC & cloth banners glue. Watch our videos to get full information of the procedure. https://www.youtube.com/watch?v=SAiekt8iVdg https://www.youtube.com/watch?v=MqsqBjgtWTM
Benson Polymers provide Polyfix fabric glue to paste cloth banners to metal frames. It is a medium viscosity adhesive which helps in bonding the substrate to metal frames easily. This adhesive takes about a minute to get initial pasting & does not need any clamping or temporary mailing to get full strength. The usage is convenient & hassle-free. Please spare a minute to watch our https://www.youtube.com/watch?v=MqsqBjgtWTM .
Flex to flex pasting can be achieved easily & instantly by using Polyfix flex grade adhesive. It is used to make bigger banners, which are usually mounted on high altitudes. Due to high wind pressure, the bonding fails & the banner gets torn. Polyfix flex adhesive is a thin cyanoacrylate adhesive which acts immediately & gives absolute permanent bonding. The strong pasting received with it can withstand winds & harsh climatic conditions.
Polyfix flex adhesive works well up to temperatures as high as 90°C and have good water resistance, however, too much exposure to extreme heat will cause the strength of the bond to weaken and similarly, exposure to too much water, especially warm water will also cause the bond to weaken.
Polyfix flex glue is made up of cyanoacrylate, an acrylic resin that reacts to form tight chains between two materials being bonded, when it comes into contact with moisture in the air.
The UV adhesives, change their form from liquid to solid by cross-linking which is a chemical reaction. The liquid chemicals of the adhesive receive the activation energy for crosslinking from UV light photons.
Just keeping the surface to be bonded anywhere, will not work. However, you can leave it in the sunlight but it will take a lot of time. UV light lamps & torches are available for the same & their intensity can also be controlled.
Polyfix provides an excellent Black Ca adhesive for this. It is an ideal filler adhesive which can be used to hide & fill any cracks on wood, granite, stone etc.
Polyfix offers two types of wood fillers. Polyfix Wood Seal is a clear CA adhesive & Polyfix black cyanoacrylate glue is black in colour. Both these adhesives can be used to fill wooden cracks & gouges. These CA adhesives are single component, which are heat & water resistant also. Gives excellent pasting & strength.
DropBond UV Glue 3036, is a premium grade for UV adhesive range by Benson Polymers Ltd. It is the best adhesive to paste glass to metal. This adhesive cure quickly upon exposure to UV light for the fast assembly of metal to glass, potting critical components, and large-area bonding. This high-impact product is resistant to yellowing and thermal shock and also designed for applications where a flexible glass-bonding adhesive is required.
Polyfix adhesives, can be used for numerous tasks. Our instant glue along with Polyfix spray activator can be used to coat wood surfaces also. It can provide proper shine to objects. It does not require any professional help. You can do small coating tasks yourself. It will give instant shine to your furniture, wooden handicrafts, table tops etc. in no time.
Apply a coat of Polyfix Instant Glue & use Polyfix spray activator on the surface. It will give a glossy & protective layer to the furniture. Polyfix instant glue is heat & water resistant, which is why it is ideal for this task and makes the furniture weatherproof.
If you apply a coat of Polyfix instant glue & use polyfix spray activator on it, it can give it a shiny, coating which can protect it from any stains.
DropBond UV adhesives are ideal to bond glass to glass. We offer Dropbond 3030 & 3036 for the same application. 3030 can be used for horizontal bonding, whereas 3036 is a more premium grade which is stronger & can bond glass to glass vertically also.
Polyfix low viscosity wood seal dries instantly. Black wood filler’s curing time can be expedited by using Polyfix spray activator.
Polyfix wood seal & Black CA adhesive can be used to fill cracks & holes in wood & can make it useful again. It can be used to repair old furniture also.
Polyfix wood seal & black CA adhesive both are cyanoacrylate based, which makes them instant in curing & strong in nature.
Acrylics are often transparent & because of this they need clear pasting. Ordinary adhesives leave white or yellow marks on the surface. Polyfix Acrylic glue gives clear & strong pasting in minimum time.
Polyfix offers special acrylic grade for bonding acrylic pieces together. It is a non-blooming adhesive which leaves no marks on the surface & is ideal to provide bonding to acrylic objects.
Polyfix acrylic adhesive is cyanoacrylate based non blooming adhesive. It does not have any water content in it.
Polyfix offers Debonder to remove cured or uncured adhesive from any surface. It can also be used to correct bonding mistakes.
Ordinary acrylic adhesives leave white or yellow stains on the surface after curing. Polyfix acrylic adhesive is a non-blooming adhesive which does not leave any marks on the surface & gives clear pasting.
Polyfix acrylic adhesive has water resistance properties. Our acrylic glue is so strong that it is even used to make acrylic fish tanks.
Polyfix offers a lot of adhesives for different applications. We offer CA based acrylic non blooming adhesive which can be used to paste acrylic sheets without any stains. We also provide DropBond 3036 UV glue to paste acrylic to acrylic. CA glue cures with moisture in the air & UV glue cures with the help of UV torch/lamp or natural sunlight.
Wood glue is used as a bonding agent for wooden pieces whereas a wood filler is used to fill the holes & cracks on a wooden surface. Polyfix provides both wood glue, which is instant & high viscosity adhesive to bond wooden surfaces, & wood filler which can fill the cracks, gouges & holes on wooden surface. We also provide Polyfix Black CA Adhesive, which can also be used to fill cracks and gouges on wooden surface and can make the unusable wood look good and usable again.
Polyfix provides instant wood glue which is cyanoacrylate based. PVA glue is the water based white adhesive. Polyfix’s Polywood is a superior & upgraded version of normal PVA glue. Normal PVA glue can only work with wood to wood pasting but Polywood can work for lamination on walls, wood boards also. It can bond wood to PVC sheets, acrylic sheets, charcoal sheets etc even if it’s a vertical application also.
Polyfix offers two different adhesives for wood. Polyfix instant wood glue is a CA based adhesive which is instant & high viscosity. Polywood is a water-based adhesive which is an upgraded version of the normal PVA glue. Both these products give strong bonding & durability.
Polyfix instant high viscosity glue is ideal to paste ceramic tiles to wood. Both of these are porous substrates & thin adhesives get absorbed by them. Polyfix high viscosity adhesive is thick & chokes the pores on the surface to give best bonding.
Polywood, a product by Benson Polymers ltd is an upgraded white glue which is capable of pasting non-porous substrates also. It is water & heat resistant, gives flexibility & durability to the substrate being bonded.
Benson Polymers provides instant wood glue, which is a cyanoacrylate based adhesive & gives instant pasting. Polywood is a white wood adhesive which is used widely in woodworking. Polyfix wood seal is a wood filler which helps in filling holes present on the wooden surface. Along with Wood seal, we also provide Polyfix Black CA adhesive which can be used to fill cracks & repairing of wood.
Polyfix high viscosity super glue, by Benson Polymers Ltd is one of the most popular brands of cyanoacrylate glues. Apart from bonding other substrates, Polyfix high viscosity glue is ideal in applications related to tile pasting.
No, cyanoacrylates glues are polymer-based formulation. Therefore, it’s not conductive.
Polyfix High Viscosity glue is heat resistant. It can be used for bonding substrates at high temperature.
Polyfix low viscosity glue is instant in curing, it takes only 3-5 seconds to set. If you want more repositioning time, then you should use high viscosity glue which cures within a few minutes. However, high viscosity glue’s curing time can also be expedited by using Polyfix Spray Activator.
Polyfix adhesives are made with quality products & under strict supervision of experts. Polyfix adhesives are instant curing, versatile in nature, gives superior strength, promises durability & are cost effective also.
Polyfix Instant Adhesive is used to make acrylic fish tanks, which are required to hold good amount of water throughout. It works great in this application. Water resistance of our adhesives is quite high.
Polyfix instant adhesive is ideal to stop leakage from terrace tiles. Just apply Polyfix to the joints in tiles & forget about any water leakage.
If used with Polyfix wood seal, baking soda can fill the gap on wooden surfaces. Using baking soda helps in making a rock-solid bond.
Super glues generally release white fumes while curing which results in white/ yellow stains on the surface. Polyfix offers Non-Blooming grade adhesive also which does not leave any marks. Polyfix Spray Activator also possess non-blooming properties.
Polyfix high viscosity adhesives are ideal for vertical applications. Being thick in nature, these adhesive does not drip while being applied on vertical surfaces. These are also best for applications where adhesive flow is crucial and the surfaces are rough and porous.
Polyfix High Viscosity adhesive is best for wood bonding. Low viscosity adhesives are thin which gets absorbed by the porous wooden surface but the high viscosity adhesive is thick which resists the absorption & initiates the adhesion quickly.
Oxygen present in air behaves like an inhibitor preventing the polymerization of monomers and hence anaerobic grades are only half filled.
No, anaerobic adhesives do not mandatorily require primer for both active or passive metals.
Only fast curing anaerobic adhesive will work on oily surfaces. For slow curing anaerobic adhesives, the presence of oil may reduce strength properties.
The vapor of cyanoacrylate monomer reacts with the atmospheric moisture depositing a white powder on the surface of the bonded area. This is known as fogging.